Tuesday, March 1, 2016

Mud Room/Backpack wall!



Pinterest teased me! Someone posts this beautiful mudroom/backpack wall (pic on the left) and no matter where I click, there is no "how-to". It's simply a picture someone liked. Sigh. 

So I took it upon myself to recreate it myself! This is my first major project all on my own. My rendition is on the right. 




I assume anyone reading this to recreate it themselves knows a thing or two about woodworking, so I'll keep my directions directed at those people. Here we go! 

I made 2 basic bookshelves to my desired height. I used Ana White's plan for her Skyscraper bookshelf (plans here) as a basic model, adjusting measurements as needed. 

I had Home Depot make the cuts (I really need a table saw!) and they didn't do a great job. BE BOSSY. If they want to make 2 cuts on one board by marking once, say something! Mark, cut. Then mark again. Rookie mistake. 

 These pictures basically walk you through the steps spelled out for you in Ana's plans. Marked my shelf lines...

            

 
 drilled my kreg jig holes...

 I wonder where my boys get their furrowed brows.


This part really was a lot easier with the hubs holding the shelves at a (roughly) 90 degree angle for me and putting good pressure there while I buried the kreg jig screws. So get a buddy to help you.


My little helpers. Doesn't get much cuter than this! 

 




Putting on the trim. Wood glue and clamps and nails. 


I made a lot of mistakes in this project, which I guess I should have expected. One being that the bookshelf on the left was going to be flat against the wall. So I shouldn't have put the trim on that edge. Fixed it later. 


Ta-DA!!!!!!!! I was so silly proud.  Sand with 220 grit before painting! 


Painting time! Two coats. I researched and researched and ended up not putting a top coat over the 2 coats. I didn't want a yellowing effect that some said might happen, and so I'm gambling that they hold up. 



My youngest LOVES ladybugs. So this one is for him. 


This was JANUARY. So hot. Ah, life in the desert. 

I used 2 panels of wainscoting from Home Depot to cover the wall between the shelves and the back of the bookshelves. I had to use a couple smaller pieces on one of them, but I just hid the seams behind the shelves.  




Hubs helped me learn how to use the circular saw. It has always intimidated me, but I got the hang of it! Note: you really should cut pretty-side-down to avoid chipping. And you should probably use a straight edge as a guide; we're rebels that way.


Used the air compressor and nailed the paneling onto the shelves. Used too long of nails and they shot out all over the place. Another mistake! 


Prepping the wall. I put a fresh coat on the parts that would be exposed. I'm a bright-color person, so I kept it a happy yellow (color is Ginger Ale).  Then I marked out my studs for anchoring the shelves into the wall. 



I used L-brackets to anchor, 2 on each. I also had to use a jigsaw to cut holes for the bookshelf to hug the molding. 


Putting the wainscoting up, I opted out of gluing, as I don't want the wall to be a mess for anyone who is going to take this off someday. Just used the nail gun. Little caulk (when I got to that point) to cover the holes, and it looked like they weren't even there! 




Excuse the dirty outlet! Cutting this hole was a challenge. Used the Dremel. Thankfully my measurements were close enough that it worked! I measured how far up from the bottom molding, and how far it was from the left bookshelf. And look at the adorable outlet cover I found!! Love it!!


ANOTHER mistake: I cut the 2nd piece from the wrong side! UGH!! Again, the caulk really saved me here, and you can barely notice my mistake. Whew! I painted the wainscoting the same color as the shelves. It's Antique White, so not too far from the white prime on it, but noticeable enough to me.  

NEXT: the hooks. I waited to cut everything for the middle section until it was time, so I could be certain of the measurements. At first I got a 1x4, but with the molding I wanted made the hooks too cramped, and it somehow warped after I painted it, so I couldn't screw it into the studs. I wound up taking it off and getting a 1x6 and it worked beautifully. 


Here is how it was going to look with the 1x4. I didn't want that space in the back, either. 


Pre-drilled starter holes 


First attempt. You can see how it's bowed. 


2nd attempt with the 1x6! Ahhhhh. So much better!!! Glued molding on before painting. 


Now on to the bench! I used this basic plan: Click Here 
Such an easy plan! 
Cut, sand, kreg jig, done! 


Mid-sanding.




Here is what I used to finish the bench. First time using this 3x stuff. Love it.  


First things first: make sure it fits! I was very happy to see that it was a snug fit.


Pre-stain wood conditioner on! 

  
Here is after the stain.


After 2 coats of poly! Beautiful. This is my favorite part of the whole thing. 


And DONE. Caulk the cracks/seams. 


Here is a before picture. There was a piano there in the opening.



Here is my inspiration, Megan. She introduced me to the joys of woodworking! 

The shelves are now full of games and books for the kids, and we are so happy with it! I am working on a sign to hang above the hooks. I will share it when I'm done.